金属对催化还原处理TNT废水降解产物的研究

研究了TNT及其还原产物色谱分析方法,鉴定了铜-铁金属对还原柱处理TNT废水所产生的降解产物,并对这一还原反应的机制进行了探讨.动力学研究结果表明,金属对还原柱还原TNT的反应是一级反应.     

有毒有害蒸气云扩散的危害估算

因事故排放形成的有毒有害蒸气云,有可能造成爆炸、火灾、中毒等危害后果,但危害后果的大小(危害程度),则与事故造成危害的时刻(延迟时间)有关。笔者在以往研究成果基础上,考虑该因素,并通过引入正态分布假设,时、空变换及误差分析,给出了估算危害程度(特别是延迟爆炸危害)的有效而简便方法,补充了以往危害估算方法(不考虑延迟时间)的不足,提高了危害后果估算精度,可广泛应用于生产安全评价、环境风险评价、风险工程设计、事故应急预案、事故应急救援等工作领域,对于保障环境安全具有显著的科学价值与现实意义。     

TNT当量法预测某石化设备爆炸后果评价

以烃化反应器为模拟发生泄漏事故源,泄漏的物料形成爆炸性气体,发生爆炸事故,采用TNT当量法预测爆炸事故后果,通过公式,计算出因爆炸冲击波导致肺出血而引起死亡的概率为0.5的半径.     

湿式空气氧化法处理TNT红水的影响因素

使用湿式空气氧化技术与生物技术联合处理TNT精制阶段所产生的红水，研究了湿式空气氧化过程中反应温度、反应时间、初始压强和pH值对流出物的COD值与流出物可生化性的影响规律。研究结果表明，随着反应温度和反应初始压强的升高、反应时间的延长、催化剂投加量的增加和反应pH值的降低，出水COD值均有所下降。在温度为300℃、初始压强为14MPa、反应时间为2h、pH值为5，3、铁盐催化剂添加量为2g的条件下，出水COD值为498mg／L，COD去除率可达到99．27％。在温度为300℃、初始压强为11MPa、反应时间为1h、pH值为3、添加1g铁盐催化剂的条件下：反应流出物的BOD5／COD值为0．301，此时可生化性已经得到很好改善。通过生物方法对反应流出物后续处理发现，湿式空气氧化技术处理TNT红水在反应温度300℃以上，反应流出物均可生物降解。     

Localization of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene (TNT) in poplar and switchgrass plants using phosphor imager autoradiography

Phosphor imager autoradiography is a technique for rapid, sensitive analysis of the localization of xenobiotics in plant tissues. Use of this technique is relatively new to research in the field of plant science, and the potential for enhancing visualization and understanding of plant uptake and transport of xenobiotics remains largely untapped. Phosphor imager autoradiography is used to investigate the uptake and translocation of the explosives 1,3,5-trinitro-1,3,5-triazine (RDX) and 2,4,6-trinitrotoluene within Populus deltoides × nigra DN34 (poplar) and Panicum vigratum Alamo (switchgrass). In both plant types, TNT and/or TNT-metabolites remain predominantly in root tissues while RDX and/or RDX-metabolites are readily translocated to leaf tissues. Phosphor imager autoradiography is further investigated for use in semi-quantitative analysis of uptake of TNT by switchgrass.     

堆肥化处理TNT红水污染土壤

DNTS[二硝基甲苯磺酸盐,主要包括2,4-DNT-3-SO₃-(2,4-二硝基甲苯-3-磺酸盐)和2,4-DNT-5-SO₃-(2,4-二硝基甲苯-5-磺酸盐]是TNT (2,4,6-三硝基甲苯)红水污染土壤中主要污染物质,为研究堆肥化对土壤中DNTS的降解效果,采用有机废物堆肥方法,探讨堆肥化对TNT红水污染土壤中DNTS降解的可行性,以及温度、含水率和pH变化对降解效果的影响.结果表明,有机废物堆肥能处理TNT红水污染土壤,在堆肥60 d内,5个堆肥体系(猪粪+木屑、猪粪+麦壳、污泥+木屑、污泥+麦壳和马粪+木屑)对2,4-DNT-3-SO₃-的降解率为65.5%~88.4%,对2,4-DNT-5-SO₃-的降解率为60.9%~100%.在第4天各堆肥体系的高温阶段(29.7~53.6℃),5个堆肥化体系中2,4-DNT-3-SO₃-总量的49.5%~67.3%被降解,说明各堆体的中温-高温阶段对有机物的降解起重要作用.堆体含水率随堆肥时间的延长呈下降趋势,在堆肥第8天,外源补水至体系含水率为50%,猪粪+麦壳体系对2,4-DNT-3-SO₃-的降解率从70.2%增至88.4%,说明适当的外源补水可提高2,4-DNT-3-SO₃-的降解率.5个堆肥体系中pH均呈初期上升、后期下降并趋于稳定的趋势,但在整个堆肥过程中,堆体pH始终保持在7.3~8.3之间.研究显示,5个堆肥体系中猪粪+麦壳体系对DNTS的降解率最高,分别为88.4%和100%.      

物化-生物组合工艺处理TNT红水

采用酸析+微电解+混凝沉淀+减压蒸馏+固定化微生物滤池+活性焦吸附组合工艺处理兵器八○五厂(襄樊分部)的TNT红水,出水中的硝基化合物浓度多小于0.8 mg/L,且多次未检出;COD最高值为76 mg/L,平均值为51.6 mg/L;色度为20°;苯胺浓度全部小于1 mg/L,达到了中试方案提出的要求,出水水质指标符合《兵器工业水污染物排放标准火炸药》(GB14470.1-2002)的要求.中试期间设备没有发生堵塞、燃烧等事故,减压蒸馏装置正常稳定运行,证实了减压蒸馏法处理TNT红水的安全可靠性.     

报废梯黑铝装药提取制备硫酸铝工艺研究

为回收梯黑铝混合装药中的铝,通过单因素试验及五因素四水平正交试验对提取工艺进行优化。结果表明,五因素影响顺序为:酸液浓度>颗粒尺寸>反应温度>液固比>反应时间;提取最佳工艺条件为:酸液浓度0.8 mol/L,炸药颗粒尺寸40~50目,反应温度45℃,液固比13 mL/g,反应时间90 min;所得硫酸铝产品品质较优。     

液体火箭共底破裂爆炸安全设防距离

针对航天发射场一旦发生低温推进剂泄漏而导致火箭爆炸,会对人员和财产造成重大损失的问题,采用TNT当量模型和TNO(The Netherlands Organization)多能模型计算不同摩尔百分比的氢氧推进剂混合反应时产生爆炸冲击波的危害性,并模拟爆炸冲击波造成的事故影响范围,然后对两种模型的仿真结果加以对比分析,根据最不利原则选取出最终需要的结果,最后划分出安全设防距离。由仿真结果可知,不同的氢氧混合摩尔百分比造成的爆炸后果不同,同时TNT当量模型在爆炸近场处高估了爆炸超压值,在爆炸远场处低估了爆炸超压值,而TNO多能模型在理论上有效地对这一缺陷进行了弥补。对航天发射场的安全布局起到了一定的参考价值。     

Study on the dynamic response of polyurea coated steel tank subjected to blast loadings

Steel tanks are widely used in the storage of various chemical liquids, and the blast resistance of the tanks is very important because of the explosiveness of these liquids. To explore a feasible method to improve the blast resistance of steel tanks, the effect of polyurea coating on the blast resistance of steel storage tank is investigated in this paper. The responses of monolithic steel tanks and polyurea coated tanks under blast loads are studied by field blast experiments using TNT explosive, and the results shows that the polyurea layers are effective in reducing the maximum and residual displacements of the tank. Numerical simulations are performed and validated, and the deformation process and stress and strain distribution of the tanks are analyzed accordingly. The increase on the bending moment of the plastic hinge lines of the tanks and the increase of the area density of the cylindrical shell induced by the polyurea layers are believed to be the two main factors contributing to the displacement reduction effect of polyurea in this paper. The validated numerical model is used to study the influence of polyurea layer's thickness on the deflection of the tank, and a nearly inversely proportional relationship between the thickness and the maximum displacement is found. Three deformation modes of the tanks are identified when subjected to blast load with varying intensity and it is found that the displacement reduction effect of polyurea varies in different deformation modes.